Month: October 2020

How to Install Exterior Plywood Siding

Plywood can be an affordable and appealing house siding. As it is wood, it can be finished with stain for a natural look or be painted any color. It installs than wood planks or shingles because it comes from panels. It is also possible to buy it for panels that can match walls high in various lengths. You can also choose from several surface finishes, from simple to feel resembling cedar. Like every wood, it be painted or resealed frequently and also has to be protected from moisture.

Nail metal flashing in the wall. Install exterior insulation or any rigid foam board over the basic home sheathing and wrap the home with a moisture barrier, typically a polystyrene sheet. Seal the backs of the panels and all edges with primer paint or wood sealer.

Use a level chalk line to snap around the home. Nail 2-by-2-inch ledger boards to the sill plates on the wall level on this lineup to support the panels; use 1/2- or 5/8-inch plywood to make a flush facet, with the plywood, foam board and sheathing. Make the ledgers adjust to the height of the panels, typically 9 ft on most exterior walls.

Place the initial panel in the back corner of the house that is quite visible from the road. Twist it with the ledger board along with the wall ; double-check with a level to make sure that it’s plumb and that the inside edge of the plank is at the middle of a wall chimney. Leave a gap of about 1/4 inch in the corner.

Fasten the panel with a hammer and galvanized finishing nails. Drive nails about 6 inches apart on the plank edges, about 12 inches in each single stud. Work in the corner into keep the plank side don’t nail both edges and then try to nail the centre. Place the minds of the nails if you plan to paint and fill out the holes; utilize in case you’re going to stain it nails that are colored to match the color of the wall.

Install panels onto the front of the wall, butting tiles together or using the tongue-and-groove overlapping that can be found at outside plywood suppliers. Check each panel with a level to be sure that it is plumb. Cut about windows, doors and other protrusions with a saw or jig saw. Quantify the cuts attentively, but leave openings of about 1/4 inch whatsoever edges to be covered by trim.

Cut panels work your way round the home to end from the road at the back corner least visible and lengthwise at corners. Install panels in the starting corner across the back of the home until you reach the corner with side panels.

Caulk all panel edges in the corners and in the roof intersection. Wood trim, typically boards, around all walls and windows in which the walls panels match the roof soffit and across the bottom to cover the ledger. Fasten cover plates over outlets, around other openings and dryer vents.

See related

How Can I Write a Land Lease Agreement?

If a property lease arrangement is not drafted carefully, it won’t really constitute a legally binding contract. There are lots of components that have to be included in a well-drafted property lease arrangement to ensure its viability. Luckily for first-time landlords, the practice is not too intricate or packed with legal jargon. If you strategy lease drafting with the right information you’re able to create a transparent, powerful, binding rental to your property property.

Provide a legal description of this property in the very first paragraph of this rental arrangement. Even though a street address or device number often suffices for structural leases, a property lease arrangement demands a more exhaustive legal description. You have to mention the property’s exact boundaries as given by coordinates on a property survey map or on the property’s deed.

Use specific, constant nomenclature when referring to parties involved in the rental. In other words, you wish to consistently and specifically refer to the”renter” and”landlord,” or use a business name or the landholder’s title in place of the generic”landlord.” Avoid using vague pronouns such as”us,””them,””that he” or”you.” These words are not specific enough and will frequently weaken a rental arrangement.

Establish the lease’s length clearly and concisely. If you do not specify how long the tenant will lease the property, then the rental arrangement is invalid.

Add any essential clauses regarding profit-sharing if you expect the tenant to give you a proportion of their property’s profits. If the property is being leased for agricultural purposes, you might wish to consider incorporating profit-sharing clauses. According to the University of California’s Small Farm Program, rents that include profit-sharing can be helpful in the event the land is fertile and the landlord and tenant both take proactive measures toward ensuring that a high crop yield. But, remember that profit-sharing agreements are usually coupled with a very low or nonexistent monthly rent, thus if the harvest fails, you won’t get rent from the tenant. Make sure any profit-sharing provisions are clearly worded, incorporating exact profit percentages and itemizing the tenant’s responsibilities for cultivating and harvesting the property.

Detail each party’s financial responsibilities for any possible construction or landscaping on the house. If your property lease arrangement enables the landlord or tenant to construct commercial or residential structures on the house, you must explain who’ll pay for these developments. In accordance with”California Real Estate Property Management,” you cannot force a tenant to pay for developments unless the lease specifically indicates that the tenant is liable for specific itemized property additions.

Any included or excluded utilities. If certain water, electrical or gas utilities are not itemized in the rental, whoever uses the utilities will be legally responsible for these invoices. Typically the tenant uses the utilities, but it can be difficult to show tenant usage in the event the house is shared by multiple occupants. This is why itemized utility prices are important in the land lease arrangement.

Schedule a consultation session with an attorney once you’ve drafted the rental arrangement. Here is the only way to know for sure that the rental is complete and legally binding. Even though it can be costly and time consuming to have a lawyer draft a rental from scratch, a simple consultation using your pre-drafted lease document will usually take around 15 minutes.

See related

How to List a FSBO Home on MLS

The National Association of Realtors reports that 85% of U.S. houses are sold through a broker utilizing the multiple listing service. Only licensed realtors and brokers are allowed access to the MLS. Because of this, sellers of FSBO houses need to go through an agent or agent to list a home on the MLS. Instead of being charged a 6% real estate agent commission, you can list your FSBO home on the MLS for a flat fee. This fee is much less than an agent’s commission.

Select a real estate agent or brokerage site that provides MLS solutions for FSBO sellers; ListbyOwnerinMLSEast is 1 alternative. Many MLS subscription services let nationwide exposure for each listed property to FSBO sellers. Contrary to popular notion, there is not just one enormous MLS. There are lots of separate MLS databases in various cities and countries. Make sure you enter your property into the MLS for your local region, not just nationally. You have to enter some simple property information to acquire the FSBO MLS procedure started. You can even upload photos of this property. A normal listing usually comes with a dedicated web page for your FSBO property. The actual estate agent or brokerage company will utilize the information you submit to invent your MLS information in a few days.

Sign the agent listing agreement next. Prior to your listing can be accepted to be added to the MLS, an agent or broker will need you to be under a signed listing agreement. The actual estate agent or brokerage business will provide you with a phone number and/or email address to contact them. This procedure can take a few days, based on the quantity of business the company will.

Check to see that the MLS listing for your property is created and published online. As you need to rely on an agent or agent to finalize your MLS posting, it is sensible to check to find that the listing is live and that the information included is correct. It may take two to seven days before your listing goes live in the MLS. At that point, your property is available on national and worldwide broker websites that share property listing information.

See related

How to Change

Homeowners can save money by changing their present mortgage loan to an interest-only mortgage. A normal mortgage loan contains interest and principle payments. Because donations are not initially made toward the principle balance, an interest-only loan frequently includes a lower payment. According to the Federal Reserve site, most fixed-rate mortgages have adjustable rates of interest that change over the period of the loan. Refinancing your current loan may enable you to acquire an interest-only mortgage.

Review your credit report before contacting a mortgage lender. This will provide an opportunity for you to dispute mistakes on your credit report and to pay any past due items or delinquent accounts. There is that A credit report in good position can place you.

Details from your lender. Your lender can provide various fee and rate options for interest-only loan products. Ask for an investigation that reflects the benefits of getting an interest-only loan from the present loan.

Shop for loans that are interest-only in the Lending Tree website. You can review offers from lenders that engage in the Lending Tree network.

Convert your present mortgage loan by applying for an interest-only mortgage loan. Choose the lender that offers rates, terms and fees that are acceptable to you. You need to finish a lender-provided mortgage loan program, in addition to national and state disclosures.

Meet with a settlement agent to examine and sign the final documents on your interest-only mortgage loan.

See related

How Can I Refinance a Rent-to-Own Mortgage?

Much like test-driving a vehicle, renting to own is an excellent way to try it before you buy it. Purchasing a new home is a leap of faith. The actual estate agent can’t know whether the neighbor’s teenager always has parties on Saturday nights, or if another neighbor’s dog barks all day long during the work week because it is left alone. If you rent to own the home, you can reside in the home for a few months or annually and decide if it’s where you really want to live until you refinance into a conventional mortgage.

Determine in the event that you genuinely possess a rent-to-own mortgage or a rent-to-own rental. Rent-to-own mortgages are called property contracts, and the purchaser does not actually rent the property. The seller financing the cost of the home without altering the labeled ownership of their property. The name changes to the purchaser only when the property contract is refinanced, and any liens on the property which the seller owes are paid in full when the home is refinanced.

Supply your mortgage creditor with a copy of your property contract and be ready to provide canceled checks Maintaining your payment history. Lenders scrutinize land contract refinances carefully. While each lender has its own rules, many won’t refinance property contracts which are less than 1 year-old. They’ll require the house be funded as a purchase rather. If the lender believes the transaction for a purchase, the purchaser may have to provide extra funds for a deposit.

Get all additional documentation required by your creditor to your new loan. The lender will require income documentation such as pay stubs, W-2s and possibly tax returns. The creditor may also require bank statements if funds are needed to close, or so the loan application requires documenting some economies. Forward these documents to your lender as soon as possible.

Stay in contact with your lender during the procedure. Your lender will require extra items or wish to schedule an assessment of the home. All of these are normal and customary things required on each loan. If your creditor requests any extra documentation, such as extra pay stubs or letters of justification, provide them as soon as possible. Work with your lender until the loan is fully approved and your loan closes.

See related

Woodipedia: Walnut Wows in Traditional and Modern Settings

Walnut is a pick for architectural millwork and conventional furniture. However, it became the wood of midcentury designers, too. With the current resurgence of that fashion, walnut is again being selected to achieve a contemporary look in house interiors. It is a “smoking hot wood” nowadays, says Dave Paulsen, a salesman at Bohnhoff Lumber in Vernon, California.

Verner Architects

The Basics

While there are numerous types of pine trees, black walnut — juglans nigra — is the commercially harvested type for home-related uses. The majority of it comes in the fundamental U.S. states. The thickness of its brownish colour will change, and it may have a reddish, purple or grey cast. Black walnut typically includes a rather straight grain pattern and is famous for its reliable toughness.

Odhner & Odhner Fine Woodworking Inc..

Cost: While the price of hardwoods varies regionally, the same as the price of gas, walnut sells for about $5 a plank foot wholesale. Much like all hardwoods, the price of walnut plummeted for some time because of decreased domestic demand. Americans purchased furniture created and then the housing market crashed and, combined with it.

However, due to tremendous demand in China, and to a lesser extent Canada, the price of walnut is skyrocketing. According to a report printed by Bill Luppold, an economist at the U.S. Department of Agriculture Forest Service, a vast percentage of chosen walnut is exported to China as whole logs. What’s more, the Chinese aren’t returning the walnut back as finished furniture, since it is considered a standing wood there.

Since there are many people who want the appearance of walnut with no paying its high price, it is not uncommon for manufacturers to stain or dye other less expensive woods in walnut tones. The term “walnut finish” generally implies that it is not authentic walnut.

Simplicity of use: Woodworkers love walnut. “It is rather simple to use,” notes Josh Salsbury, who functions at actor Nick Offerman’s woodshop in Los Angeles and whose table is revealed here. “It machines easily, does not burn like maple and is secure. Plus it smells pretty great when you cut it.”


Types of Walnut

You’ll sometimes hear about British walnut, but that species is grown primarily for commercial nut harvesting or within an ornamental yard tree.

Butternut, also known as white walnut, is an “incidental species,” says Jim Steen of Pike Lumber in Indiana. It is a lighter shade of brown but is no longer a “competitive species,” he says, since it has been beset with a fungal disease for the previous 20 years. Butternut is a very soft wood, on the purchase of poplar or alder, and isn’t considered commercially viable.


Claro walnut is a beautiful multicolored walnut that comes chiefly from Northern California and the Pacific Northwest. After harvesting, it is ordinarily air-dried instead of kiln-dried, which averts the gorgeous range of color stripes found inside a single plank.

Ultra-tec Cable Railing From The Cable Connection

Not walnut: Ipe (pronounced EE-pay) is frequently referred to as Brazilian walnut, but it is out of a different genus and is therefore not a true walnut. Other woods that aren’t true walnuts are African, Caribbean and Patagonian “walnut”


Thick, live-edge walnut slabs are very popular for countertops and tabletops and are rather easy to discover. Slabs work well in both modern settings atop a metal table base as well as in more rustic state chambers.

Signature Innovations LLC


The Janka score measures a wood’s resistance to dings and dents. The scale ranges in the softest wood (quipo, at 22) into the hardest (Australian bull walnut, at 5,060). Black walnut is rated 1,010 (lbs of power). That positions walnut as “somewhat hard,” a little below hard maple (1,450) and white pine (1,360).

TreHus Architects+Interior Designers+Builders


Walnut is a fantasy to complete. It sands into a highly polished luster and takes any kind of sealing coat without difficulty. The biggest difficulty is addressing the problem of sapwood, which is the dramatically light-colored wood found in the outermost section of the tree. Some folks enjoy the natural variations between the light-colored sapwood and the darker-colored heartwood. If you discover the combination too active for your tastes, you can stain the wood to even it out.

If you’re likely to apply a paste wax to walnut, be sure to use a dark-colored wax. Should you use a neutral shade, the wax will dry into a milky color in cracks and crevices, whereas the dark-colored wax will blend in.

Lisa Ferguson Interior Design

UV Stability

While lots of woods — maple, such as — patinate over time, walnut gets lighter as it ages. “Walnut isn’t UV stable,” notes professional wood finisher Brian Miller, who has revived many Greene and Greene historic landmark homes in Los Angeles. “Despite a complete coat, it still lightens with age”



regardless of the current high need for black walnut and its comparative rarity in hardwood woods, walnut is still a sustainable resource. The majority of all timberland in this nation is independently owned, and professional foresters are generally hired to maintain the health of these properties. They follow best-practice guidelines and eliminate just dead, dying, diseased or damaged trees.

The American Hardwood Council says that the volume of hardwood in American woods is currently 90 percent larger than it had been 50 years back.

Matthew MacCaul Turner

A cautionary note. Forester Jim Steen says dying or dead walnut trees should not be hauled elsewhere in the place where they’re cut. This is because these trees may possess Thousand Cankers black walnut disease, which is spread mostly via the movement of raw wood to some other site.

The Wonder of Walnut: A Love Story
Maple Is a Marvel Around the Home

See related

Patterns Mingle Spiritedly in a Toronto Condo

Tim Lam enjoys a good design challenge. As an interior designer, he has made them his livelihood. His first residence, a 30-year-old condominium overlooking Lake Ontario at Toronto, presented quite a few hurdles too. For one, mirrored walls screamed “I love the ’80s,” while an equally outdated kitchen and bathroom lacked color and texture. Lam injected the 750-square-foot area with layers of picture patterns and added budget-friendly storage options that saved distance. He oversaw all of the renovations, learning how to take care of new design challenges along the way.

at a Glance
Who lives here: Tim Lam
Location: Harbour Front, Toronto
Size: 750 square feet; 1 bedroom, 1 bath
That’s intriguing: Lam located the home with the Assistance of Sandra Rinomato and the HGTV series Property Virgins.

Jenn Hannotte / Hannotte Interiors

Lam selected neutral colors for the significant pieces in the living room. A spoonful of red comes in the vintage Saarinen Womb Chair. He made the curtains and a few of the throw pillows with fabric from Tonic Living. He credits his style into his late mother, who appreciated everything classic, classy and elegant.

Floral cushions: Mint Fleur Chinoise, Caitlin Wilson Textiles; carpeting: Facet, DwellStudio; coffee table: Caban (currently closed); white side table: Style Garage; wall paint: Wedding White, ICI; trim paint: White Husky, ICI

Jenn Hannotte / Hannotte Interiors

A blue characteristic wall enhances light pouring in from the west windows. Lam and Paul Duguay Restoration reupholstered the couch, a Salvation Army locate, and also the chair, from Queen Street Antiques, with material from Designer Fabrics.

Blue paint: Vista, Para; artwork on blue wall: Suzanne Ernst

Jenn Hannotte / Hannotte Interiors

“It took me a couple of years to figure out what I wanted to do with my closetless bedroom,” Lam says. “Clearly, storage is a key concern in a 750-square-foot condominium, and that I did not need a huge piece of furniture sitting in my bedroom” He made this custom made walnut wall unit and added Ikea pieces.

Pillows, curtains, headboard: Tonic Living; wood device installment: Paul Duguay Restoration

Jenn Hannotte / Hannotte Interiors

Organic-looking wallpaper covers the wall opposite the bed.

Dresser: Style Garage

Jenn Hannotte / Hannotte Interiors

Lam darkened the palette at the dining area to create an intimate and elegant area. Classic midcentury pieces in rich wood tones create balance.

Background: Maharani, Sariskar, Osborne & Little; carpeting: Alvine Rand, Ikea; chairs: vintage Cherner, eBay

Jenn Hannotte / Hannotte Interiors

A large floor mirror doubles the visual area.

Mirror: HomeSense

Jenn Hannotte / Hannotte Interiors

Lam painted the existing cabinetry. The flooring, countertops, backsplash and appliances are all new.

Cabinet door paint: Silver Cloud, ICI; cabinet frame paint: Cielo Blanc, ICI; custom spray: Tim Welsby, Beresford; knobs: Quatrafoil, Rocky Mountain Hardware; carpeting: HomeSense

Jenn Hannotte / Hannotte Interiors

To add another area to his home, Lam maximized his outdoor balcony area. He found the coffee table around the side of the road. Tim Welsby of Beresford spray its own foundation.

Love chair: Loblaws, reupholstered by Wesley Seto Design; fabric: Designer Fabrics; floral pillow fabric: Crystal Lake at Midnight, Robert Allen

Jenn Hannotte / Hannotte Interiors

Lam replaced the vanity, mirror, shower and flooring tile in the bath.

Jenn Hannotte / Hannotte Interiors

A number of those leftover ’80s design remains celebrated. A mirror wall at the entrance reflects a combination of classic and midcentury pieces.

Jenn Hannotte / Hannotte Interiors

Tim Lam, shown here, says that his second design challenge is sourcing wallpaper because of his hallway.

Show us your condominium makeover!

Read more houses by style:
Small Homes | Colorful Homes | Eclectic Homes | Modern Homes | Contemporary Homes
Midcentury Homes | Ranch Homes | Traditional Homes | Barn Homes | Townhouses | Apartments | Lofts | Vacation Homes

See related

Falling for Colour: 9 Ways With Pumpkin Orange

With Halloween right around the corner I only had to catch the chance to provide some love to one of my favorite colors: pumpkin orange. The key to working with this extreme color would be to use it to get those areas or items in your home that you would like to listen to. Then be sure to select coordinating colors wisely.

Coordinating colors similar to orange — colors of brown, reddish or yellow — can create your palette colorful yet harmonious. Colors of blue (the match(reverse of orange on the colour wheel) will make a dynamic, high-energy vibe. The more colour shy one of you might want to put this extreme orange entirely with neutrals.

You may use it to warm a mostly white or gray contemporary interior, to keep the space from feeling overly crude. Or you can use it to add some vibrancy to a traditional space that’s possibly heavy on dark neutrals or deep wood tones. I’ve gathered nine examples which illustrate precisely how gorgeous and versatile this color could be in a home, along with six of my preferred pumpkin-inspired paint colors.

Stedila Design

Jennifer Ott Design

1. Accent Wall

Sure, they are a clear way to use a bold colour in a space, however I remain a loyal fan of accent partitions. An eye-popping colour such as this on all four partitions may feel overwhelming, especially if the space lacks plenty of natural lighting. I therefore tend to advise homeowners to utilize it on only a couple of walls. Or on the ceiling.

Get a similar look with Pumpkin Patch from Behr.

jones | haydu

Jennifer Ott Design

2. Kitchen Backsplash

I like to utilize neutral colors for items that I do not wish to change out for many, many decades, like flooring and kitchen countertops and cabinets. But it does not have to have a huge quantity of work or a huge cost to update a backsplash farther down the road if you grow tired of the colour, especially if your backsplash area is quite small. So why not go for a orange colour? When paired with rich and white forests, as in the case shown here, it creates a look that is clean and contemporary, yet warm and inviting.

Get a similar look with Pumpkin from Valspar.

RisherMartin Fine Homes

Jennifer Ott Design

3. Accent Stripe

A little pumpkin orange goes a long way, so if a full accent wall is too much shade for you, think about having a mere stripe of the colour. This is a cool style for a child’s or teen’s room. And since it’s such a little bit of colour, you may allow the child select the hue.

Get a similar look with Pumpkin Pie from Benjamin Moore.

Moore Design Group

4. Furniture

Should you favor walls, ceilings and flooring in neutral colors, think about adding a fun orange shade in your own decor. Furniture can get expensive, so you should make certain to love this colour and would like to keep it around for a while, but the nice thing about using furniture or decorative accessories to get a jolt of color in a space is they are rather simple to update.

David Howell Design

5. Lighting

One of my favored, and more unexpected, ways to bring bold colour into an area is through light fixtures. Lighting now comes in all sizes, shapes and colors, and I love making a bold-hued ceiling fixture the centerpiece of a space. It draws up the eye and can make the space look larger.

Iba Design Associates

6. Cabinet Interior

Give your prized possessions the attention they deserve by painting the trunk or interior of your pajamas or screen cabinet a feisty colour of orange. You might also add a splash of colour to the interior of a built-in niche. Pick up the colour in small pieces throughout the space to help move the eye around the space.

Watch more ideas for vivid cabinet interiors

Jennifer Ott Design

Get a similar look with Harvest Pumpkin from Behr.

Juliette Byrne

7. Nondecorative Accessories

Consider a fun colour for even the most utilitarian items in a space. I love the option of orange to the storage containers and binders here. It offers the office a joyful, fun vibe.

Atkinson Pontifex

8. Outdoor Wall

Take bold orange outside with an exterior accent wall. This is a great colour for outside spaces in a chilly or moist climate, since it can provide a warm glow during the cold autumn evenings.

Jennifer Ott Design

Get a similar look with Pumpkin Cream from Benjamin Moore.

BAR Architects

9. Front Door

regardless of the style of your home, you can not fail with a pumpkin-orange front door. But if you opt for this hue for the door, I recommend sticking with much more neutral colors for the siding and trim, unless your home is minimalist and modern in style. That is because the more clean and easy the traces of the home, the easier it is to pull off a bold color palette without the whole thing’s appearing overly busy.

Check out more tips about painting your front door orange

Jennifer Ott Design

Get a similar look with Fall Gala from Valspar.

Read more about picking colors for your home

Inform us : Are you a fan of bold pumpkin colors? How have you used them in your home? Post your pictures from the Comments section below.

See related

Educate Old-World Style New Tricks

Being an antiques dealer’s daughter subjected me to the attractiveness of old-world design from a really young age. Growing up, I had been surrounded by 19th-century wall clocks, sterling silver trays and crystal. Naturally, as I developed (along with my design taste), I decided to rebel against my upbringing and be a lover of this intense minimalist design movement. However as more time passed, I discovered that beauty can be found in the ability to combine opposing design styles into one lively interior. So I was inspired to share with my fellow ers several interiors that signify an outstanding job of bridging the best of both worlds.

The designers of this gorgeous interior allowed the classical architectural details of this room to set the stage for its few well-selected modern treasures. A fantastic rule of thumb when dealing with more than 1 style in an area is to pick a dominant fashion along with a complementary accent design.

LDa Interiors & Architecture

This dining room showcases how the mostly modern style of the furnishings may contrast beautifully against the conventional feel of this fireplace and moldings.

Watch the rest of this home

Peter A. Sellar – Architectural Photographer

When it comes to kitchens, you could go in two distinct directions: select conventional cabinetry to contrast with a couple of modern accents (such as the lamps at the interior above) or…

Elad Gonen

… select ultrasleek and modern cabinetry to contrast with a rustic dresser-turned-island. No matter which style dominates, pick contrasting colors which are few but have a large impact.

Neuhaus Design Architecture, P.C.

When it comes to living spaces, ensure your design plays against the architectural details you already have from the room. As an example, this space boasts incredible details from the crown moldings, crystal chandelier and fireplace remedies. The designers have offset the classical background with a few very modern and minimalist pieces of furniture.


In case you have a modern room to start with, purchase one or two antique pieces with a lot of detail work. They will contrast beautifully against the surfaces of your modern design, as showcased by the picture above.

Watch the rest of this home

Neuhaus Design Architecture, P.C.

Another room that greatly benefit from the juxtaposition of old and new is your bathroom. The very same rules apply: be certain you use the architectural details of this room to your advantage. In this case, the designer has been able to decide on an ultramodern tub and chandelier to contrast the rest of the traditional decor.

Watch the rest of this home

Jane Kim Design

If, however, you weren’t blessed with architectural information from the 1800s, you may always complement your sleek and modern bathroom with a classic iron-claw bathtub.

Watch the rest of this home

LDa Interiors & Architecture

An extra method of bringing old-versus-new contrast to your space is by way of storage. In this case, the conventional architectural details of this foyer are paired with the modern horizontal grain and minimalist design of this built-ins.

Erdreich Architecture, P.C.

On the other hand, the modern lines of this room are a beautiful and uncluttered background for the elaborate armoire and chairs, attaining an ideal balance of textures.

Tell us Have you used an old-new interior design in your interiors? What practical advice can you give your fellow ers on successfully developing a cohesive space? Share below.

Find your design style

Relax and Enjoy an Extreme Style Mix
Home Styles: New Traditional Design

See related